The number on your lens is the number you need
Lens caps are sized by the diameter of the front thread, usually printed on the lens barrel or the inside of the old cap. That number—46mm, 105mm, or anything else—is the only measurement that matters for a snap-on front cap. A cap designed for a 46mm thread will not fit a 105mm lens, and no amount of squeezing will change that.
If you are replacing a lost cap, check the lens itself rather than guessing from the filter size you use. The thread diameter is the same specification, so a 105mm filter and a 105mm cap share the same front thread. The same logic applies to a 46mm lens: look for a 46mm cap.
How to measure your lens cap size
You can confirm the size in under a minute with the lens in front of you.
- Check the lens barrel: Look for a number followed by mm near the front rim, often next to the filter thread symbol. This is the most reliable source.
- Look inside the old cap: Many caps have the diameter moulded into the plastic on the inner face. If the old cap fits well, that number is your replacement size.
- Measure the thread if markings are missing: Use a ruler across the inner diameter of the front thread, from one side to the other. Measure in millimetres and round to the nearest whole number.
- Confirm before ordering: If your measurement falls between two sizes, re-check the lens barrel. Caps are made to specific diameters, not adjustable ranges.
Why centre-pinch caps are easier with a lens hood
A centre-pinch cap uses a squeeze-and-spring mechanism in the middle of the cap. You pinch the centre to release it, which means your fingers do not need to reach the outer edge of the lens. That matters when a lens hood is mounted, because the hood often leaves little space around the rim for a traditional side-pinch cap.
The same design also helps if you shoot with gloves or have limited hand strength. The trade-off is that centre-pinch caps can be slightly bulkier in the middle, but for most photographers the convenience outweighs that difference.
Two sizes in the Kood centre-pinch range
- Kood 105mm Centre-Pinch Snap-On Front Lens Cap with Keep Cord: Kood 105mm Centre-Pinch Snap-On Front Lens Cap with Keep Cord: designed for any lens or filter with a 105 mm diameter front thread. If your lens barrel or old cap reads 105mm, this is the direct replacement size. The centre-pinch mechanism is specifically noted as easier to remove when a lens hood is mounted.

Kood 105mm Centre-Pinch Snap-On Front Lens Cap with Keep Cord - Kood 46mm Centre-Pinch Snap-On Front Lens Cap with Keep Cord: Kood 46mm Centre-Pinch Snap-On Front Lens Cap with Keep Cord: designed for any lens or filter with a 46 mm diameter front thread. A 46mm thread is common on smaller primes and kit lenses. This cap matches that diameter and uses the same centre-pinch design.

Kood 46mm Centre-Pinch Snap-On Front Lens Cap with Keep Cord
The keep cord: a small feature that prevents a common loss
Both Kood caps include an integrated keep cord. The idea is simple: attach the cord to your camera body so the cap stays tethered while the lens is in use. That eliminates the risk of setting the cap down on a wall, in a pocket, or on a bench and forgetting it.
The cord does not change the fit of the cap. It is an addition to the cap itself, and the cap still attaches to the lens thread in the same way. If you often remove your cap in the field, the cord is the difference between a cap that stays with you and one that becomes a replacement purchase.
46mm vs 105mm: what changes in use
The two sizes serve different lenses, but the handling is the same. The choice is purely about matching your lens thread.
- 46mm lens cap: Fits lenses with a 46mm front thread. Typically found on smaller lenses where the front element is more compact. The centre-pinch mechanism works the same way as on the larger cap.
- 105mm lens cap: Fits lenses with a 105mm front thread. Larger diameter caps can be more awkward to grip from the edge, which is where the centre-pinch design becomes especially useful.
What the catalog does not confirm
The supplied product information does not list the exact lens models each cap fits beyond the thread diameter. It also does not confirm whether the keep cord has a specific attachment method or length. If you need those details, check the cap in person or contact the store before ordering.
The catalog also does not state a compatibility list for filters beyond the thread diameter. A 105mm cap is designed for a 105mm filter thread, but the fit with a particular filter brand is not confirmed in the supplied information.


